 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HMC826LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 990 - 1105 MHz Features * RF Bandwidth: 990 to 1105 MHz * Fractional or Integer Modes * 19-Bit Prescaler * Ultra Low Phase Noise -110 dBc/Hz in Band Typ. * Figure of Merit (FOM) -227 dBc Integer * 24-bit Step Size, Resolution 3 Hz typ * 200 MHz, 14-bit Reference Path Input * Cycle Slip Prevention * Read / Write Serial Port, Chip ID * 40 Lead 6x6mm SMT Package: 36mm2 Typical Applications 12 PLLS w/ INTEGRATED VCO - SMT * Cellular/4G Infrastructure * Repeaters and Femtocells * Communications Test Equipment * CATV Equipment * Phased Array Applications * DDS Replacement * Very High Data Rate Radios Functional Diagram 12 - 98 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC826LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 990 - 1105 MHz General Description The HMC826LP6CE is a fully functioned Fractional-N Phase-Locked-Loop (PLL) Frequency Synthesizer with an Integrated Voltage Controlled Oscillator (VCO). The synthesizer consists of an integrated low noise VCO with divideby-2 output, an autocalibration subsystem for low voltage VCO tuning, a very low noise digital Phase Detector (PD), a precision controlled charge pump, a low noise reference path divider and a fractional divider. The fractional synthesizer features an advanced delta-sigma modulator design that allows both ultra-fine step sizes and low spurious products. The phase detector (PD) features cycle slip prevention (CSP) technology to allow faster frequency hopping times. Ultra low in-close phase noise and low spurious also allows wider loop bandwidths for faster frequency hopping and low micro-phonics. For theory of operation and register map refer to the "PLLs w/ Integrated VCOs - RF VCOs" Operating Guide. To view the Operating Guide, please visit www.hittite.com and choose HMC826LP6CE from the "Search by Part Number" pull down menu. Electrical Specifi cations, TA = +25 C VPPCP, VDDCP, VCC1, VCC2 = 5V 4%; RVDD, AVDD, DVDD3V, VCCPD, VCCHF, VCCPS = 3.3V 6% GNDCP = GNDLS = Ground Paddle = 0V Parameter Condition Min. Typ. Max. Units 12 1980 990 8 11 15 -2 -25 -23 -31 -33 1.5 2210 1105 15 MHz MHz dBm MHz/V MHz/V dBc dBc dBc dBc RF Output Characteristics VCO Frequency at PLL Input RF Output Frequency at f VCO/2 RF Output Power at f VCO/2 VCO Tuning Sensitivity VCO Supply Pushing RF Output 2nd Harmonic RF Output 3rd Harmonic RF Output 4th Harmonic RF Output 5th Harmonic Measured at 2 GHz, 2V Measured at 2 GHz, 2V RF Divider Characteristics 19-Bit N-Divider Range (Integer) 19-Bit N-Divider Range (Fractional) Max = 219 - 1 Fractional nominal divide ratio varies (-3 / +4) dynamically max 16 20 524,287 524,283 REF Input Characteristics Max Rep Input Frequency Max Ref Frequency with AutoCal Min Ref Input Frequency Ref Input Range Ref Input Capacitance 14-Bit R-Divider Range 1 AC Coupled 1.5 200 54 100 2 3.3 5 16,383 MHz MHz kHz Vpp pF Phase Detector (PD) PD Frequency Fractional Mode PD Frequency Integer Mode Max PD Freq. Min VCO Freq/20 Max PD Freq. Min VCO Freq/16 0.1 0.1 88 110 MHz MHz Charge Pump Max Output Current Min Output Current Charge Pump Gain Step Size (5-Bits) 2 500 500 mA A A For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 - 99 PLLS w/ INTEGRATED VCO - SMT HMC826LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 990 - 1105 MHz Electrical Specifi cations (Continued) Parameter Charge Pump Trim Step Size (3-Bits) Charge Pump Offset Step Size (4-Bits) PD/Charge Pump Noise 1 kHz 10 kHz 100 kHz Less than 3 dB degradation typ. at these limits Compliance Voltage -385 A Offset +385 A Offset 0.4 0.8 VPPCP-0.8 VPPCP-0.4 V V 50 MHz Ref, Input Referred, Integer, add 6 dB for Fractional -141 -149 -155 dBc/Hz dBc/Hz dBc/Hz Condition Min. Typ. 7 55 Max. Units A A 12 PLLS w/ INTEGRATED VCO - SMT Logic Inputs VIH Input High Voltage VIL Input Low Voltage DVDD3V-0.4 0 DVDD3V 0.4 V V Logic Outputs VOH Output High Voltage VOL Output Low Voltage DVDD3V-0.4 0 DVDD3V 0.4 V V Power Supply Voltages Analog 3.3V Supplies Digital Supply Analog 5V Supplies AVDD, VCCHF, VCCPS, VCCPD, RVDD DVDD3V VPPCP, VDDCP, VCC1, VCC2 3.0 3.0 4.8 3.3 3.3 5 3.5 3.5 5.2 V V V Power Supply Currents +5V Analog Charge Pump +5V VCO Core and PLL Buffer +5V VCO Divider and RF Buffer +3.3V Analog +3.3V Digital Power Down - Crystal Off Power Down - Crystal On, 100 MHz VPPCP, VDDCP VCC2 VCC1 AVDD, VCCHF, VCCPS, VCCPD, RVDD DVDD3V Reg 01h=0, Crystal Not Clocked Reg 01h=0, Crystal Clocked 100 MHz 5.3 56 36 45 6.5 10 10 200 mA mA mA mA mA A A Power on Reset Typical Reset Voltage on DVDD Min DVDD Voltage for No Reset Power on Reset Delay 1.5 250 700 mV V s VCO Open Loop Phase Noise at fvco/2 1 GHz Divide-by-2 Output 1 GHz Divide-by-2 Output 1 GHz Divide-by-2 Output 1 GHz Divide-by-2 Output 1 GHz Divide-by-2 Output 10 kHz Offset 100 kHz Offset 1 MHz Offset 10 MHz Offset 100 MHz Offset -91 -121 -146 -163 -164 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz Closed Loop Phase Noise PLL + VCO at fvco/2 1 GHz VCO, Integer, 50 MHz PFD 1 kHz Offset -112 dBc/Hz 12 - 100 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC826LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 990 - 1105 MHz Electrical Specifi cations (Continued) Parameter 1 GHz VCO, Integer, 50 MHz PFD 1 GHz VCO, Integer, 50 MHz PFD 1 GHz VCO, Integer, 50 MHz PFD 1 GHz VCO, Fractional, 50 MHz PFD 1 GHz VCO, Fractional, 50 MHz PFD 1 GHz VCO, Fractional, 50 MHz PFD Condition 10 kHz Offset 100 kHz Offset 1 MHz Offset 1 kHz Offset 10 kHz Offset 100 kHz Offset Normalized 1 Hz Measured w/ 50 MHz PD at 30 kHz Offset Measured w/ 50 MHz PD at 30 kHz Offset -227 -225 dBc/Hz dBc/Hz Min. Typ. -114 -120 -146 -107 -107 -112 Max. Units dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz Figure of Merit Integer Mode Fractional Mode 12 -80 -90 1000 MHz FF 1050 MHz FF 1100 MHz FF -80 -90 990 MHz FF 1105 MHz FF 1020 MHz FF PHASE NOISE (dBc/Hz) -110 -120 -130 -140 -150 -160 -170 2 10 PHASE NOISE (dBc/Hz) -100 -100 -110 -120 -130 -140 -150 -160 -170 2 10 10 3 10 4 10 5 10 6 10 7 10 8 10 3 10 4 10 5 10 6 10 7 10 8 OFFSET FREQUENCY (Hz) OFFSET FREQUENCY (Hz) VCO/2 Free Running Phase Noise -40 -60 Typical VCO/2 Tuning Curves vs. Switch Position 1100 n0 n2 n4 n6 n8 n10 n12 n14 n16 n18 n20 n22 n24 n26 PHASE NOISE (dBc/Hz) -80 -100 -120 -140 -160 -180 3 10 N0 1126 MHz N15 1038 MHz N31 960 MHz 1050 kvco (MHz/V) 1000 950 n30 n31 10 4 10 5 10 6 10 7 10 8 900 0 1 2 3 4 5 OFFSET FREQUENCY (Hz) TUNING VOLTAGE (V) [1] Fractional Mode, 50 MHz Crystal, R=1, ~80 kHz Loop BW, Filter C36 = 560pF, R26 = 680, C35 =15nF, R27 & R28 = 1 k, C37 & C38 = 270 pF, 2mA Charge Pump, -385A Offset. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 - 101 PLLS w/ INTEGRATED VCO - SMT Closed Loop Integer Phase Noise Typical Closed Loop Fractional Phase Noise [1] HMC826LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 990 - 1105 MHz Free Running VCO Phase Noise (VTUNE Set by AutoCal) -110 100kHz Offset Typical VCO Tuning Voltage After Calibration TUNE VOLTAGE AFTER CALIBRATION (V) 5 50MHz PFD, 500kHz Tuning Steps, +25C 256 Count Calibration ,195kHz Resolution 31usec Total Cal Time -120 PHASE NOISE (dBc/Hz) -130 -140 -150 10MHz Offset 100k +27C 100k +85C 100k -40C 1MHz Offset 4 3 31 15 0 2 -160 -170 950 1 990 1030 1070 1110 1150 0 920 960 1000 1040 1080 1120 1160 12 PLLS w/ INTEGRATED VCO - SMT 60 50 FREQUENCY (MHz) CALIBRATION FREQUENCY (MHz) Typical VCO Sensitivity vs. Cap @ Fo Voltage Typical Spurious at 200 kHz from Integer Boundary [1] 0 1000.200 MHz 50 MHz PFD Fractional Mode 200 kHz Offset from Integer Boundary 70 kHz Loop Bandwidth PHASE NOISE (dBc/Hz) kvco (MHz/V) 40 TUNING CAP 31, Fmin AT 2V TUNING CAP 15, Fmid AT 2V TUNING CAP 0, Fmax AT 2V 200 kHz 400 kHz -60 30 Typical Operating Range 20 -120 10 0.09 deg rms jitter DSB Integ Phase Noise 100 Hz to10 MHz -56 dBc 0 0 1 2 3 4 5 -180 2 10 10 3 10 4 10 5 10 6 10 7 10 8 TUNING VOLTAGE (V) FREQUENCY OFFSET (Hz) Typical Output Power - Narrow Band Match 20 See Matching Network Figure of Merit NORMALIZED PHASE NOISE (dBc/Hz) -200 OUTPUT POWER (dBm) 15 -210 Typ FOM vs Offset -220 FOM 1/f Noise FOM Floor 10 5 +27C +85C -40C -230 0 920 -240 960 1000 1040 1080 1120 1160 10 2 10 3 10 4 10 5 10 6 OUTPUT FREQUENCY (MHz) FREQUENCY OFFSET (Hz) [1] Fractional Mode, 50 MHz Crystal, R=1, ~80 kHz Loop BW, (Loop filter values: C36 = 560pF, R26 = 680, C35 =15nF, R27 & R28 = 1 k, C37 & C38 = 270 pF) 2mA Charge Pump, -385A Offset. 12 - 102 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC826LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 990 - 1105 MHz Pin Descriptions Pin Number 1 2, 5, 6, 8, 9, 11 - 14, 18 - 22, 24, 26, 34, 37, 38 3 4 7 10 15 16 17 23 25 27 28 29 30 31 32 33 35 36 39 Function AVDD Description DC Power Supply for analog circuitry. The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. Power Supply for charge pump analog section Charge Pump Output Power Supply for the charge pump digital section Reference Supply Reference Oscillator Input DC Power Supply for Digital (CMOS) Circuitry Chip Enable. Connect to logic high for normal operation. VCO Varactor. Tuning Port Input. VCO Analog Supply 2 VCO Analog Supply 1 VCO Divide by 2 RF Positive Output VCO Divide by 2 RF Negative Output PLL Serial Port Enable (CMOS) Logic Input PLL Serial Port Data (CMOS) Logic Input PLL Serial Port Clock (CMOS) Logic Input Lock Detect, or Serial Data, or General Purpose (CMOS) Logic Output (GPO) DC Power Supply for Analog Circuitry DC Power Supply for Analog Prescaler DC Power Supply for Phase Detector External bypass decoupling for precision bias circuits. Note: 1.920V 20mV reference voltage (BIAS) is generated internally and cannot drive an external load. Must be measured with 10G meter such as Agilent 34410A, normal 10M DVM will read erroneously. N/C VPPCP CP VDDCP RVDD XREFP DVDD3V CEN VTUNE VCC2 VCC1 RF_N RF_P SEN SDI SCK LD_SDO VCCHF VCCPS VCCPD 12 PLLS w/ INTEGRATED VCO - SMT 12 - 103 40 BIAS For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC826LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 990 - 1105 MHz Absolute Maximum Ratings AVDD, RVDD, DVDD3V, VCCPD, VCCHF, VCCPS VPPCP, VDDCP, VCC1 VCC2 Operating Temperature Storage Temperature Maximum Junction Temperature Reflow Soldering Peak Temperature Time at Peak Temperature ESD Sensitivity (HBM) 260C 40 sec Class 1B -0.3V to +3.6V -0.3V to +5.8V -0.3V to +5.5V -40C to +85C -65C to 125C 150C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 12 PLLS w/ INTEGRATED VCO - SMT 12 - 104 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC826LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 990 - 1105 MHz Outline Drawing 12 NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number HMC826LP6CE Package Body Material RoHS-compliant Low Stress Injection Molded Plastic Lead Finish 100% matte Sn MSL Rating MSL3 Package Marking [1] H826 XXXX [1] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 - 105 PLLS w/ INTEGRATED VCO - SMT HMC826LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 990 - 1105 MHz Evaluation PCB 12 PLLS w/ INTEGRATED VCO - SMT The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. 12 - 106 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC826LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 990 - 1105 MHz List of Materials for Evaluation PCB 128147 [1] Item J1, J2 J3 J4, J5 C1, C15 - C17, C25, C29 C2, C3, C6, C7, C11, C12, C14, C18, C27, C43 C4, C13 C5, C33 C8 C19 - C24, C28, C30 - C32, C34 C26 C35 C36 C37, C38 C39 - C42 FB1 - FB2 R1, R2, R5, R11, R15, R18, R19 R3, R4, R6, R7 R8 R12, R20, R23 R22, R25 R24 R26 - R28 L1 TP3, TP4 U1 U2 Y1 PCB [2] Description PCB Mount SMA RF Connector Dual Row Terminal Strip Connector Header 10 F Capacitor, 0805 Pkg. 0.47 F Capacitor, 0402 Pkg. 22 pF Capacitor, 0402 Pkg. 1000 pF Capacitor, 0402 Pkg. 1.5 pF Capacitor, 0402 Pkg. 0.1 F Capacitor, 0402 Pkg. 1.0 F Capacitor, 0603 Pkg. 3300 pF Capacitor, 0402 Pkg. 270 pF Capacitor, 0402 Pkg. 68 pF Capacitor, 0402 Pkg. 4.7 F Tantalum Capacitor, 0805 Pkg 1000 Ohm 200 mA Ferrite Chip, 0805 Pkg. Zero Ohm Resistor, 0402 Pkg. 1 kOhm Resistor, 0402 Pkg. 22 Ohm Resistor, 0402 Pkg. 51 Ohm Resistor, 0402 Pkg. 20 kOhm Resistor, 0402 Pkg. 10 Ohm Resistor, 0402 Pkg. 1k Ohm Resistor, 0402 Pkg. 12 nH Inductor, 0402 Pkg. Test Point PC Compact SMT HMC826LP6CE PLL with Integrated VCO Low Noise Quad Adjustable Linear Regulator 3.3V, 50 MHz VCXO Crystal Oscillator 125998 Evaluation Board 12 PLLS w/ INTEGRATED VCO - SMT 12 - 107 [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR and FR4 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com |
Price & Availability of HMC826LP6CE
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |